Home » CalChem
Calmag CalChem 3-in-1 Central Heating Chemical Inhibitor
CALCHEM
Improve Heating Performance Today
The Calmag CalChem 3-in-1 chemical inhibitor is a powerful all-in-one solution designed to clean, restore, and protect central heating systems.
Unlike standard inhibitors, CalChem combines cleaning, corrosion protection, and antifreeze properties in a single treatment, making it ideal for systems that have not been powerflushed or previously treated.
Learn more about our central heating chemicals.
CalChem works immediately on contact with contaminants inside your system, targeting:
- Sludge and debris
- Limescale deposits
- Flux residues
- Bacteria and algae
Its advanced formula helps restore heating efficiency while protecting against future damage.
- All-in-one solution (cleaner + inhibitor + antifreeze)
- Restores system efficiency
- Reduces boiler noise and radiator issues
- Prevents corrosion and limescale buildup
- Lubricates valves and pumps
- Suppresses bacteria and gas formation
- Easy to use – add and leave in system
- Suitable for all system types (including aluminium and copper)
- Domestic central heating systems
- Boilers and radiators
- Older or untreated systems
- Maintenance and system upgrades
- Add via radiator, filling loop, or header tank
- Leave circulating in the system
- 1 litre treats approx. 10–15 radiators
Header Tank
- Turn off boiler
- Locate drain tap at the bottom of a radiator. Attach a hose to drain tap, ready to run drain. Do not open the drain tap at this point. Please note: a hose clip may be required to fasten to the hose tap to prevent spillage.
- Locate the header tank and turn off supply. The header tank is normally located in the roof space, or loft. If unsure as to which is the cold water tank and which is the header tank, then run the hot and cold taps in a bathroom unit until the cold water tank’s make up runs dry.
- Open the drain at the bottom of the radiator and drain off water. When the header tank has drained, close the tap.
- Turn the make up back on and add the chemical at the dosage rate into the system whilst refilling the header tank. Dosage rate should be at 10% of the total system make up – on a system with 10-15 radiators. 1 litre should be sufficient.
Pressurised System
- Turn off boiler and take note of the pressure.
- Locate drain tap at the bottom of a radiator. Choose the lowest point within the heating system to ensure that all the system will be treated.
- Attach a hose to the drain tap, ready to run to drain. Open the drain tap. Please note: a hose clip may be required to fasten to the hose tap to prevent spillage.
- Locate a radiator at the top of the heating system and open the air vent. Air should now rush in. Continue draining the system until the chosen radiator has drained approximately 30% (3-4 litres). Turn off the drain and remove the hose.
- Unscrew the air vent plug at the top of the radiator.
- The CalChem can now be added into the system using a funnel. Alternatively, a clean washing up liquid bottle can be filled with the CalChem and squirted directly into the system at the correct dosage – on a system with 10-15 radiators, 1 litre should be sufficient.
- Screw the air vent plug back into the radiator. Ensure that PTFE tape is used for the air vent plug thread.
- Refill the system to the operating pressure noted at the outset and vent the radiators to remove any air.
- Venting may also be required in 2-3 days after the initial vent, and avoid spillage by taking precautionary measures when used. Ensure that any excess fluid is wiped off all surfaces and fittings.
This product is ideal when:
- A system has not been powerflushed
- No inhibitor has previously been used
- You are experiencing:
- cold spots on radiators
- boiler noise
- poor heating efficiency
It’s a fast alternative to full system cleaning
3-in-1 Protection Explained
1. Cleaning Action
Breaks down sludge and system debris, improving circulation and heat transfer.
2. Corrosion & Scale Protection
- Rust and corrosion
- Limescale formation
- System deterioration
3. Antifreeze Protection
Includes antifreeze properties to protect systems during colder months and prevent freezing damage.
FAQS
What is a 3-in-1 heating chemical?
It combines cleaner, inhibitor, and antifreeze in one solution.
Item Do I still need power flushing?
Not always—this is designed for systems where flushing hasn’t been done.
How often should I add CalChem?
Typically every 1–2 years for ongoing protection.
CHAT TO AN EXPERT
Please fill in your details and one of our team will get back to you as soon as they can. Or, give us a call on 0800 093 8222
Our offices are open Monday-Friday 08:30-17:00
COMMERCIAL
APPLICATIONS?
solutions designed to combat the issues of limescale
in any business.






