Calmag CalChem 3-in-1 Central Heating Chemical Inhibitor

CALCHEM

Improve Heating Performance Today

 

The Calmag CalChem 3-in-1 chemical inhibitor is a powerful all-in-one solution designed to clean, restore, and protect central heating systems.

Unlike standard inhibitors, CalChem combines cleaning, corrosion protection, and antifreeze properties in a single treatment, making it ideal for systems that have not been powerflushed or previously treated.

Learn more about our central heating chemicals.

CalChem works immediately on contact with contaminants inside your system, targeting:

  • Sludge and debris
  • Limescale deposits
  • Flux residues
  • Bacteria and algae

Its advanced formula helps restore heating efficiency while protecting against future damage.

  • All-in-one solution (cleaner + inhibitor + antifreeze)
  • Restores system efficiency
  • Reduces boiler noise and radiator issues
  • Prevents corrosion and limescale buildup
  • Lubricates valves and pumps
  • Suppresses bacteria and gas formation
  • Easy to use – add and leave in system
  • Suitable for all system types (including aluminium and copper)
  • Domestic central heating systems
  • Boilers and radiators
  • Older or untreated systems
  • Maintenance and system upgrades
  • Add via radiator, filling loop, or header tank
  • Leave circulating in the system
  • 1 litre treats approx. 10–15 radiators

 

Header Tank

  1. Turn off boiler
  2. Locate drain tap at the bottom of a radiator. Attach a hose to drain tap, ready to run drain. Do not open the drain tap at this point. Please note: a hose clip may be required to fasten to the hose tap to prevent spillage.
  3. Locate the header tank and turn off supply. The header tank is normally located in the roof space, or loft. If unsure as to which is the cold water tank and which is the header tank, then run the hot and cold taps in a bathroom unit until the cold water tank’s make up runs dry.
  4. Open the drain at the bottom of the radiator and drain off water. When the header tank has drained, close the tap.
  5. Turn the make up back on and add the chemical at the dosage rate into the system whilst refilling the header tank. Dosage rate should be at 10% of the total system make up – on a system with 10-15 radiators. 1 litre should be sufficient.

Pressurised System

  1. Turn off boiler and take note of the pressure.
  2. Locate drain tap at the bottom of a radiator. Choose the lowest point within the heating system to ensure that all the system will be treated.
  3. Attach a hose to the drain tap, ready to run to drain. Open the drain tap. Please note: a hose clip may be required to fasten to the hose tap to prevent spillage.
  4. Locate a radiator at the top of the heating system and open the air vent. Air should now rush in. Continue draining the system until the chosen radiator has drained approximately 30% (3-4 litres). Turn off the drain and remove the hose.
  5. Unscrew the air vent plug at the top of the radiator.
  6. The CalChem can now be added into the system using a funnel. Alternatively, a clean washing up liquid bottle can be filled with the CalChem and squirted directly into the system at the correct dosage – on a system with 10-15 radiators, 1 litre should be sufficient.
  7. Screw the air vent plug back into the radiator. Ensure that PTFE tape is used for the air vent plug thread.
  8. Refill the system to the operating pressure noted at the outset and vent the radiators to remove any air.
  9. Venting may also be required in 2-3 days after the initial vent, and avoid spillage by taking precautionary measures when used. Ensure that any excess fluid is wiped off all surfaces and fittings.

This product is ideal when:

  • A system has not been powerflushed
  • No inhibitor has previously been used
  • You are experiencing:
    • cold spots on radiators
    • boiler noise
    • poor heating efficiency

It’s a fast alternative to full system cleaning

3-in-1 Protection Explained

1. Cleaning Action

Breaks down sludge and system debris, improving circulation and heat transfer.

2. Corrosion & Scale Protection

  • Rust and corrosion
  • Limescale formation
  • System deterioration

3. Antifreeze Protection

Includes antifreeze properties to protect systems during colder months and prevent freezing damage.

FAQS

What is a 3-in-1 heating chemical?

It combines cleaner, inhibitor, and antifreeze in one solution.

Not always—this is designed for systems where flushing hasn’t been done.

Typically every 1–2 years for ongoing protection.

SAFETY DATA SHEET

CHAT TO AN EXPERT

Please fill in your details and one of our team will get back to you as soon as they can. Or, give us a call on 0800 093 8222

Our offices are open Monday-Friday 08:30-17:00

ARE YOU AFTER
COMMERCIAL
APPLICATIONS?
We have a range of high-performance water treatment
solutions designed to combat the issues of limescale
in any business.
Learn more

How hard is your water?

If it’s 100ppm or above, a water softener can help you avoid limescale buildup and improve skin and hair health.

* PPM stands for parts per million and indicates the concentration of dissolved limescale minerals like calcium and magnesium in water.

Contact us to today find out more

01535 210320

Chat to a Calmag Expert

Just pop your details in below and one of the team will get back to you. Or, give us a call on 01535 210320.